| Customization: | Available |
|---|---|
| After-sales Service: | 24/7 Online After Sales Services |
| Warranty: | 12 Months After Delivery Date |
|
Still deciding? Get samples of US$ 450/Piece
Order Sample
|
| Shipping Cost: | Contact the supplier about freight and estimated delivery time. |
|---|
| Payment methods: |
|
|---|---|
| Support payment in USD |
| Secure payments: | Every payment you make at Made-in-china.com is protected by the platform. |
|---|
| Refund policy: | Claim a refund if your order doesn't ship, is missing, or arrives with product issues. |
|---|
Suppliers with verified business licenses
Audited Supplier Audited by an independent third-party inspection agency
| Product advantages | ||
| Project | CAMCT | Others |
| Lower flow limit | 0.1m/ s (linear accuracy guaranteed) |
0.3m/ s (linear accuracy guaranteed) |
| Response time | 100ms | ≥3S |
| Strong steady flow function | have | Don't have |
| Product category | |||
| Medium | Conductive liquid such as sewage, chemical liquid and tap water | ||
| Output | 4-20Ma (load resistance 0~750Ω), pulse, frequency, RS485 protocol | ||
| Accuracy class | Class 0.3, 0.5 | Velocity range | 0.1-15m/ s |
| Medium temperature | -20~+160ºC | Ex-proof grade | Exd lI CT6 G |
| Protection grade | IP67, Special requirements could up to IP68 | ||
| Technical parameters | |
| Executive standards | Electromagnetic flowmeter(JJG 1033-2) |
| Nominal caliber (can be customized) | Pipe type PTFE lining: DN15-DN2000 Pipe type rubber lining: DN65-DN2000 Pipe type PFA lining: DN40-DN600 |
| Flow direction | Positive, negative, net flow |
| Range down | 150:1 |
| Repeatability | ±0.1% |
| Medium temperature | Regular rubber lining: -20ºC~+60ºC Normal temperature rubber lining: -20ºC~+90ºC PTFE lining: -30ºC~+120ºC High temperature PFA lining: -20ºC~+160ºC |
| Rated working pressure | (DN15~DN25) ≤4.0MPa (DN32~DN300)≤1.6MPa (DN350~DN800)≤1.0MPa (DN800~DN2000)≤0.6MPa |
| Velocity range | 0.1-15m/ s |
| Conductivity range | ≥5μ s / cm |
| Communication output | RS485, HART protocol, GPRS output |
| Power supply | 220VAC,Tolerance 15%or 24VDC,ripple wave≤5% |
| Required straight pipe segment length | Upstream≥5DN, Downstream≥2DN |
| Connection type | Flange connection: HG20592-2015 |
| Protection grade | IP67 |
| Ex-proof Class | ExdIIct6 Certificate No.:CE19.14 |
| Ambient temperature | -25°ºC~+60°ºC |
| Relative humidity | 5%~95% |
| Total power consumed | <7.5W |
| Measurable range | |||||
| Caliber | Min adjustable range(0.3m/s, per hour) | Max adjustable range (10m/s, per hour) |
|||
| mm | inch | m³/h | GPM | m³/h | G |
| 15 | 0.5 | 0.19 | 0.84 | 6.36 | 28.0 |
| 25 | 1 | 0.53 | 2.35 | 17.7 | 78.0 |
| 32 | 1.25 | 0.87 | 3 | 29.0 | 100 |
| 40 | 2 | 1.36 | 600 | 45.2 | 200 |
| 50 | 2 | 2.12 | 9.35 | 70.7 | 310 |
| 65 | 2.5 | 3.58 | 15.0 | 119.5 | 502 |
| 80 | 3 | 5.43 | 24.0 | 181.0 | 800 |
| 100 | 4 | 8.48 | 37.5 | 282.7 | 1250 |
| 125 | 5 | 13.25 | 60.2 | 441.8 | 2008 |
| 150 | 6 | 19.1 | 84.0 | 636.1 | 2800 |
| 200 | 8 | 34.0 | 150.0 | 11313 | 5000 |
| 250 | 10 | 53.0 | 41.0 | 1767 | 8031 |
| 300 | 12 | 76.3 | 347 | 2544 | 11565 |
| 350 | 14 | 103.9 | 472.3 | 3463 | 15741 |
| 400 | 16 | 135.7 | 616.9 | 4523 | 20560 |
| Selection list | ||||||
| ZYDC | Intelligent electromagnetic flowmeter | |||||
| M | Integral | |||||
| F | Split | |||||
| Lining material | F | PTFE | ||||
| Z | Rubber lining | |||||
| A | PFA | |||||
| Pipe connection | C1 | HG 1.0Mpa flange type | ||||
| C2 | HG 1.6Mpa flange type | |||||
| C3 | HG 2.5Mpa flange type | |||||
| E1S | DIN PN10 clamping type | |||||
| E2S | DIN PN16 clamping type | |||||
| Instrument caliber | DN15 DN20 DN25 DN32 DN40 DN50 DN65 DN80 DN100 DN125 DN150 DN200 | |||||
| Nominal caliber | ||||||
| Electrode material | L | 316L | ||||
| H | HC 276 | |||||
| Ti | Titanium | |||||
| Ta | Tantalum | |||||
| P | Platinum-iridium alloy | |||||
| N | No | |||||
| Electrode ring | S | 316L | ||||
| H | HC 276 | |||||
| Ti | Titanium | |||||
| Ta | Tantalum | |||||
| P | Platinum-iridium alloy | |||||
| Connection | ||||||
| 2 | 1/2" NPT Internal thread | |||||
| 4 | M20*1.5 Internal thread | |||||
| Power supply | A2 | 220V AC | ||||
| D1 | 24V DC | |||||
| Ex-proof | Explosion-proof sign | |||||
| N | No ex-proof | |||||
| D | Flame-proof EXD II CT6 | |||||
| Communication protocol | Communication protocol | |||||
| N | No | |||||
| H | Hart protocol | |||||
| M | Modbus protocol | |||||
| P | Profibus-PA | |||||
| Selection example: ZYDC/M/F/C2/L/DN25 | ||||||
| Explanation: intellgiengt flowmeter integrated PTFE lining flange connection 1.6Mpa 316L electrode 1/2NPT internal thread 220V AC power supply Modbus protocol | ||||||
PACKING & SHIPPING
At Shandong Zhongziyi Intelligent Technology Co., Ltd., we prioritize your satisfaction by ensuring the swift delivery of your ordered IP67 Electromagnetic Flowmeter. Our commitment is to meet your needs with punctual, reliable, and exceptional service.
The installation of the electromagnetic flowmeter varies depending on the site pipeline conditions. Flowmeters without a ball valve should be installed on a non-pressurized pipeline (i.e., non-pressurized installation allows for the selection of flowmeters without a ball valve).
A hole with a diameter of 50 should be made in the pipeline, and preparations should be made to weld a connecting pipe to the opening in the pipeline.
For situations that require continuous flow during loading and unloading or where media overflow is not permitted, a ball valve must be added, which means selecting an insertion-type electromagnetic flowmeter with a ball valve structure.
A hole with a diameter of 50 should be made in the pipeline, and preparations should be made to weld a connecting pipe to the opening in the pipeline.
| Measuring range | Recommend using range | 0.5m/s to 10m/s continuously adjustable |
| Max using range | 0.2m/s ~ 15m/s continuously adjustable |
|
| Output | The switching quantity can be set to | Pulse output (up to 1000HZ) |
| High/low flow alarm | ||
| Empty pipe alarm | ||
| Flow direction indication | ||
| Fault alarm | ||
| Current output | Output 4-20mA | |
| Configuration mode | Field configuration with three manual keys | |
| Field configuration through remote controller | ||
| Field configuration by hand operator | ||
| Memory | EEPROM memory that does not disappear and does not require battery storage |
|
The requirements for the straight pipe sections are 5D upstream and 3D downstream, ensuring the optimal operation and accuracy of the electromagnetic flowmeter.
The measurement principle of the electromagnetic flowmeter does not depend on the characteristics of the flow.
If turbulence and vortices are generated in the non-measurement area of the pipeline (such as elbows, tangential throttling, or a partially open shut-off valve upstream), it will not affect the measurement.
However, if there are steady-state vortices in the measurement area, it will affect the stability and accuracy of the measurement.
In this case, measures should be taken to stabilize the flow distribution:
1.2. Pipeline-type Electromagnetic Flowmeter
2.1. Requirements for Straight Sections To mitigate the effects of vortices and flow field distortion, there are specific requirements for the lengths of the straight pipe sections upstream and downstream of the flowmeter. Otherwise, measurement accuracy will be affected (a straightener can also be installed, and it is advisable to avoid installation close to control valves and partially open valves).
2.2. Requirements for the Process Pipes The flowmeter has specific requirements for the upstream and downstream process pipes at the installation point; otherwise, measurement accuracy will be affected. a. The inner diameter of the upstream and downstream process pipes should be the same as that of the sensor and must meet the condition: 0.98DN ≤ D ≤ 1.05DN (where DN is the inner diameter of the sensor, and D is the inner diameter of the process pipe). b. The process pipe and the sensor must be concentric, with an axial deviation not exceeding 0.05DN.
2.3. Requirements for Bypass Pipes To ensure seamless maintenance and optimal performance of the flowmeter, it is highly recommended to install a bypass pipe. This is particularly essential for flowmeters dealing with heavily contaminated fluids, or in scenarios where the flowmeter needs to be cleaned without interrupting the fluid flow. a. Facilitates easy and efficient maintenance of the flowmeter. b. Crucial for heavily contaminated fluids. c. Allows flowmeter cleaning without halting the fluid flow.
3. Installation Requirements for Insertion-Type Electromagnetic Flowmeters
3.1. Requirements for Straight Pipe Sections To maintain precision in measurements, the insertion-type electromagnetic flowmeters require specific straight pipe sections: The inlet straight pipe section should be at least 10 times the nominal diameter (≥ 10×DN) and the outlet straight pipe section should be no less than 5 times the nominal diameter (≥ 5×DN).
3.2. Requirements for Grounding Points For the instrument to operate reliably and deliver precise measurements, it must be immune to external parasitic potentials. Therefore, the sensor must have excellent grounding, with a grounding resistance of less than 10 ohms. If the metal pipeline is already well-grounded, no additional dedicated grounding device is necessary.
3.3. Requirements for Installation Position As depicted in the accompanying diagram, the precise installation position is critical to ensure optimal functioning and accurate readings from the flowmeter.
COMPANY AND FACTORY PICTURE: Shandong Zhongziyi Intelligent Technology Co., Ltd. proudly showcases its state-of-the-art facilities and innovative manufacturing processes through the company and factory images below.
){kind=link}